How to check and accept after decoration

2022-07-22
  • Detail

After the decoration is completed, many owners do not know how to check and accept, so the decoration will be in vain. Therefore, we must do a good job of acceptance to protect our rights and interests

first: paint

1 The surface color is correct and uniform, the brightness is smooth and moderate, and there is no sagging, wrinkled skin, too thick, transparent, blistering, anti whitening, etc

2. The paint boundary is straight and neat, and the wood oil is out of bounds

3. The emulsion paint can be seen at a distance of 1m without wrinkles

4. The coloring of wood nails should be accurate and smooth. Hardware fittings and glass should be clean

second: wallpaper

?? The seam of the wallpaper should be accurate, fitted, and free of blisters. The flowers should be aligned according to the regulations, and cut with a sharp blade. There should be no tearing of the edge of the paper

third: carpentry

1 Structure - when we accept the woodworking project, we check whether its structure is straight and flat (whether horizontal or vertical, the correct woodworking practice should be straight and flat)

2 Modeling - our woodworking project should have a flat surface without bulging or breakage. Symmetrical carpentry items should be symmetrical

3. Corner - in woodworking design, the normal corner is 90 degrees, except for special design factors

4. Mosaic - our carpentry project mosaic must be strict and accurate. The correct wood parquet should be seamless or keep a uniform spacing

5. Gap - the corner seam between the line and the line clamp shall not exceed 0.3mm, and the seam between the seal line, corner line and waist line shall not exceed 0.2mm, the seam between the trim panel and the plate shall not exceed 0.2mm, and the overall error of the sliding door shall not exceed 0.3mm

fourth: electrician

1 PVC pipe or black iron pipe shall be used for the line entering the wall. The method of digging the wall and burying the line cannot be used, and the road box shall be connected

2. The laying of open lines should be as neat and beautiful as possible, especially at the corner, and the distance between lines should be normal and equal

3. Wires in the cabinet shall be concealed as far as possible, and fixed with a rubber wire code every 200mm

4. High power electrical equipment (such as air conditioners, electric water heaters, etc.) should be wired separately

5. The leakage circuit breaker shall be set as the main switch in the household distribution box. The leakage action current is 30mA

6. Electrical devices should be firmly wired and well contacted. Non live metal parts should be reliably grounded and ground wires should be installed

7. The switch should be installed 1.3m above the ground. 0.2m from the door frame. The toilet socket should be splash proof

8. The weak current system and the electric lighting line shall not be laid in the same pipe and installed in the same connection box

fifth: paving

1 The tile surface should be flat, the angle should be accurate, the edges should be neat, and the edges and corners should be complete

2. The floor of kitchen and toilet should be suitable for inclined water (2%), Do not accumulate water, pour water

3. After the tiles are jointed, the cement mortar shall be brushed with rattan wire, and the residual cement mortar shall not be left on the brick surface

fifth: paving

1 The tile surface should be flat, the angle should be accurate, the edges should be neat, and the edges and corners should be complete

2. The floor of kitchen and toilet should be suitable for inclined water (2%), Do not accumulate water, pour water

3. After the tiles are jointed, the cement mortar shall be brushed with rattan wire, and the residual cement mortar shall not be left on the brick surface

sixth: Carpet

1 The seam of carpet should be aligned with the pattern and the direction of carpet wool

2. Use aluminum corner to close the edge. Don't hit it directly with a small hammer. First cushion it with wood blocks and then tap it gently to avoid dents

seventh: floor, floor wax

1 The slab joint shall not be greater than 0.2mm. The skids shall be larch, bensong and miscellaneous wood. The specification shall not be less than 45mmx25mmo, and the length of the fixing screw shall be 2-2.5 times the height of the grid

2. The newly made maple floor should be made with 9-12mm plywood as the bottom. The bottom of the board should be waterproof with linoleum or plastic paper, and 10-20mm gaps should be reserved on the four sides, which should be covered with skirting. The crystal floor should be oiled at least three times

3. The polished floor should be smooth without concave or sharp marks, and the corners should be polished with a small grinder

eighth: water supply and drainage and equipment

1 The downspout shall be based on the nearest distance and the smallest interface. The downspout shall be straight and tidy, and bending and overlapping shall be minimized

2. Copper pipes (PVC pipes) are used indoors, rubber coated copper pipes are used for hot water pipes, PVC pipes are used for sewer pipes, and raw material strips are used for interfaces

3. When installing surface accessories such as faucets, cloth tools should be used. Do not damage the faucets and accessories. It is not allowed to use a hammer to directly and vigorously knock. The installation of washbasin and toilet should be level

4. Kitchens and toilets should have drains (floor drains), especially toilets

5. Water test shall be conducted after installation, and there shall be no water seepage and leakage

tree life has always adhered to the business purpose of "quality is the life of an enterprise", and has always been pioneering and innovative in the pursuit of first-class brands. A medium and high-end integrated home customization company integrating R & D, production and sales, provides customers with complete and reliable considerate services, and helps escort customers in their pursuit of high-quality home life

?? The business tenet of "quality is the life of an enterprise" has always been to explore and innovate on the road of pursuing first-class brands. A medium and high-end integrated home customization company integrating R & D, production and sales, provides customers with complete, reliable and considerate services, and helps escort customers in their pursuit of high-quality home life

济南血液病医院

石家庄胎记医院

西安性病医院

贵阳癫痫医院

Copyright © 2011 JIN SHI